Your Ultimate Smart TV Guide to Seamless Entertainment

Vizio TV Remote Stopped Working: 10 Methods to Fix It


You’re watching your favorite movie on Vizio TV. But you want to increase the volume, so you grab the remote to change the settings. You press the increase volume button; however, your remote isn’t working. What should you do now? You’re not alone. Many users have faced the problem of their Vizio TV remote Stopped working. Generally, it happens because of low batteries, a poor power source, or residual power from the TV and remote. Before replacing your Vizio TV remote with a new one, try the methods mentioned in this article. They’ll save you time and money.

Quick Answer: You should replace your Vizio TV remote batteries with new ones, update your TV firmware, and power cycle your TV and remote. Let’s dive deeper to learn step-by-step methods and more solutions.

Methods To Fix Vizio TV Remote Stopped Working 

In this guide, you’ll learn about some of the most effective methods to solve the issue of Vizio TV remote not working. Here are some of the solutions you can implement. 

Read: Rumble on Roku

New Batteries 


It’s one of the easiest and most effective methods to get your Vizio TV remote to start working. If your remote batteries are drained, they’ll not work properly. So replace the batteries with new ones. Ensure they are properly installed, and check the connection points and battery terminals. If the battery terminals are rusted, you should clear them with alcohol. 

Inspect the Power Source Of Vizio TV 


The abnormal power quality is also known as Dirty Power. It is generally delivered to other devices, so your Vizio TV remote may show signs of not working. So how can you avoid this situation? Because of this, you may encounter power fluctuations, voltage variations, etc. To minimize this issue, change the power source by following these steps. 

  • Power off your Vizio TV. 
  • Now unplug it from the power outlet. 
  • Plug it back into a different power source and check if the remote is working now. 

Analyze TV Remote Sensor


When the TV remote’s sensor is not working, there’s usually a huge signal distortion because of a blockage between the remote and the TV sensor. As a result, your remote will not work. To get rid of this problem, here’s what you should do. 

  • Navigate the IR sensor of the TV. It is present at the bottom left or right corner of Vizio TV. 
  • If there’s any book, device, or picture in front of the sensor, then remove it. 
  • Now, point your remote directly at the TV sensor. Press the power button to check if signals are being transmitted. 

Power Cycle Your TV 

If you’re still unable to solve this problem, try power cycling your Vizio TV. Here’s how. 

  • Find the Power button on your Vizio TV and press it to turn off the TV. 
  • Now unplug the TV from the power outlet. 
  • Hold the Power button for 20 to 30 seconds. After that, release it, which will drain the residual power of Vizio TV. 
  • After that step, plug the TV into the power source again. 
  • Now, wait for a minute or more. Again, hold the Power button to turn on the TV and check the remote’s functioning. 

Power Cycle Remote


Sometimes, the Vizio TV remote stops working because of its power residue. But by power cycling the remote, you can drain all the power residue and reset temporary configurations. Here’s a quick method for doing that. 

  • Take out your remote batteries. 
  • Find the Power button on your remote and hold it for 5 seconds. 
  • Press all the buttons on your Vizio remote at least once. That way, you will clear all the residual power of the remote. 
  • Place batteries back into the remote to make your remote work again. 

Reset Remote

Have you tried all the above methods, and is your remote stubborn issue not going away? Then, you should reset your remote. This will wipe all the cache memory. Follow this method to reset your remote. 

  • Press the Set or Setup button, which is present at the top left corner. 
  • Release the button when you notice that the LED light blinked two times. 
  • Here, type the reset code for your remote. Check the reset code of your remote, but most of these remotes have reset codes of 981 or 977. 
  • Wait until the LED light flashes twice. Your remote memory will be wiped out. 
  • Now, make sure to switch it back to the TV. You can do it by using the button at the bottom of the remote. 

Check Buttons Condition 

This solution may seem small, but it can be extremely incredible. All you need to do is check if the Vizio TV remote buttons are sucked or not in the proper position. So what should you do? Release your remote buttons. Then, pat the remote against your palms a few times. 

Update Vizio TV

Updating your Vizio TV can solve many problems, including the remote not working. But you might wonder how to update your TV if the remote is not working. You can use a remote app to access the Settings menu. Follow the steps mentioned below. 

  • Install a Vizio TV remote app on your device. 
  • Use the remote to access the Settings menu. 
  • Now click on System and then Check for Updates. 
  • If there’s any new update, click Install and wait until the update is completed. Avoid turning off your phone during the updating process. 

Clean The Remote

If the remote still fails to work, clean every component of your remote properly, including the circuit board, plastic panel, etc. But why should you do that? That’s how you can remove liquid residue from the remote. The cleaning can be difficult as there are no screws on Vizio TV remote. Here’s a guide you should follow. 

  • Remove your remote batteries. Press the Power button for 30 to 50 seconds to drain residual power. 
  • Use a flat-head screwdriver to open your TV remote. 
  • Separate rubber button panel and circuit board. Now, check if there are any signs of dirt or liquid substances. 
  • Remove these stains and substances with 99% isopropyl alcohol
  • Wait until the remote is completely dry. Now, restore it to its original shape. 
  • Aim your Vizio TV remote towards the TV to analyze if it’s working. 


Q: Why does Vizio TV Remote stop working for these common reasons?

A: Inspect the Power source, change new batteries, power cycle TV, power cycle remote, update your Vizio TV, clear remote, check button conditions, reset remote.


There can be many reasons why a Vizio TV remote is not working properly. Some of the common reasons include dead batteries, issues with the IR beam, or sucked buttons. You should identify the issue and then implement a solution accordingly. But what if all the solutions don’t work? What should you do then? If nothing works, you can control the Vizio TV through the recommended remote app.

This is not only efficient but also quick to ensure your remote is working.  Still, have any queries about your Vizio TV remote? Reach out to us today via email or drop your question in the comments below. We are here to assist you and provide the best possible solution.

Share this article
Shareable URL
Prev Post

How Can I Get Local Channels on A Smart TV [2024 Guide]

Next Post

How Do You Turn Off Voice on Roku [5 Quick Methods]

Leave a Reply

Your email address will not be published. Required fields are marked *

Read next